PAK (Metroid Prime 3)
See PAK (File Format) for the other revisions of this format.
The .pak format in Metroid Prime 3 and Donkey Kong Country Returns is a new version of the pak format with some slight changes. The most notable change is that resource IDs have been extended from 32 bits to 64 bits. The new format also aligns to 64-byte boundaries, rather than 32. Aside from that, the other changes are mainly organizational; it's still largely the same data as older versions of the format.
Note that the Metroid Prime 3 E3 prototype uses a slightly modified version of the Metroid Prime pak format, not this one. See the PAK (Metroid Prime) page for more info on that revision of the format.
|
This file format is almost completely documented Research needs to be done on how to order files to optimize loads. Also, the very first part of the header is mostly unknown. |
Format
The header is split into a number of smaller chunks that are each padded to the next 64-byte offset.
Header
| Offset | Size | Description |
|---|---|---|
| 0x0 | 4 | Unknown. Always 2. |
| 0x4 | 4 | Unknown. Always 0x40. |
| 0x8 | 16 | Unknown; appears to be a hash of some kind. |
| 0x18 | End of header; pad to 64 bytes | |
Table of Contents
The next part of the file, starting at 0x40, is a brief list of each section in the pak and its size. Although it uses a count value, this section always lists the same data in the same order.
| Offset | Size | Description |
|---|---|---|
| 0x0 | 4 | Section count; always 3 |
| 0x4 | 4 | "STRG" fourCC |
| 0x8 | 4 | Named Resources section size |
| 0xC | 4 | "RSHD" fourCC |
| 0x10 | 4 | Resource Table section size |
| 0x14 | 4 | "DATA" fourCC |
| 0x18 | 4 | File data section size |
| 0x1C | End of ToC; pad to 64 bytes | |
Named Resources
This section, always starting at 0x80, lists named resources. These are the files that the game has direct access to; every other file in the pak will be a dependency of one of these.
It starts with a 32-bit count, followed by the table itself; each entry of the table is structured as follows:
| Type | Size | Description |
|---|---|---|
| string | - | Name; zero-terminated |
| fourCC | 4 | Resource type |
| u64 | 8 | Resource ID |
Resource Table
The final table contains a list of every resource in the pak. Following a 32-bit count value, each resource entry is structured as follows:
| Offset | Size | Description |
|---|---|---|
| 0x0 | 4 | Compression flag; this will either be 0 or 1, with 1 denoting a compressed file. |
| 0x4 | 4 | Resource type fourCC. |
| 0x8 | 8 | Resource ID |
| 0x10 | 4 | Size (note: always a multiple of 64; the end of the file is padded with 0xFF if necessary) |
| 0x14 | 4 | Offset (relative to the start of the DATA section) |
| 0x18 | End of entry | |
Compression
Some pak files are compressed; in Prime 3, files are compressed with segmented LZO1X, just like Prime 2. In DKCR, on the other hand, files are compressed as a single zlib stream, like Prime 1. In either game, every compressed file is formatted the same way, starting with some metadata detailing the structure of the compressed data.
| Offset | Size | Description |
|---|---|---|
| 0x0 | 4 | "CMPD" fourCC |
| 0x4 | 4 | Compressed block count |
Each compressed block is structured as follows. Note that the first byte of each size value appears to actually be a completely different value, so the three bytes following are what makes up the actual size value.
For each block, if the compressed and decompressed sizes match, that indicates the block is uncompressed.
| Offset | Size | Description |
|---|---|---|
| 0x0 | 1 | Unknown |
| 0x1 | 3 | Compressed size |
| 0x4 | 1 | Unknown |
| 0x5 | 3 | Decompressed size |
| 0x8 | End of entry | |